![]() The heart of your vinyl setup is, of course, the turntable itself. Image: Lightboxx / Alamy Stock Photo What to look for in the best turntables for home use? They also have a short lifespan and increase the risk of damaging your delicate discs. Those suitcase turntables might look stylish, but often they contain cheap, heavy tonearms and an inferior sapphire stylus instead of the industrial strength diamond that the majority of reliable turntables use). When building a vinyl system, you first and foremost need to pay attention to the build quality of your turntable. You are set to go and enjoy your vinyl collection.Wait, what about those all-in-one record players that come in a suitcase? Remove Protractor.Ĭongratulations! The turntable setup is complete. Repeat steps 2 and 3 till the cartridge is square at both points. If not, change overhang, (move cartridge in or out along the axis) until the cartridge is square. Check that cartridge is square with the inner set of grid lines. Move cartridge/ tonearm until stylus rests exactly on the center of inner bulls-eye (66.04mm radius), Rotate protractor around spindle as required. If not, loosen cartridge mounting screws and twist the cartridge lightly until it is square. Check that cartridge is square with an outer set of grid lines. Move cartridge/tonearm until the stylus rests exactly on the center of the bullseye. Place this protractor on your turntable platter with a hole over the spindle. To do this, you will need Phono Cartridge Alignment Protractor. It is vital to align the position of the cartridge with the arc of the record grooves. The cartridge has connected the headshell with two screws. Now you must perform tricky and sensitive cartridge adjustment. This is a final but very important and critical step. Now you can go further! 4. Cartridge alignment If it shows a different value (let's say 2,4 grams) adjust the counterweight till it shows the exact 2,0 grams). Release the handle and measure the weight. ![]() Put the scale on the platter, adjust it so the stylus hits the spot on the scale. To peer this, you can use the Accurate tonearm scale. Very often, the true value will be different. Good job! You are almost set, but you can perform an additional check to see is the tracking force correct. Then, rotate the anti-skating dial on the same value, 2 grams. You should simply turn the counterweight (don't turn the dial) till the dial show 2,0 on the scale. If the pressure is too high, it will damage the stylus (or even the grooves of the record), If the pressure is too low, it will produce jumps and unprecise reproduction (even the scratches on the surface). If you don't have this information, try to find it online for your cartridge. Every cartridge comes with this information (it is usually between 1.5 and 2.5 grams). This will allow the correct amount of pressure which will be produced on the record grooves. Now you need to adjust the tracking force of your cartridge. Great job! Now you have a balanced tonearm. When you finish this, put the tonearm back in place and turn the counterweight ring dial to zero. With your other hand, rotate the counterweight left or right till the tonearm is in balance (it should stand in an almost still position in the air. Release the handle and gently hold it with your arm. First, adjust the anti-skating dial to zero. To do this use the counterweight at the tonearm. Use the adjustable stands (if available) or use a sort of pad to put below the stands to level it up. Make sure that the plater surface is totally horizontal and check it on three points. Remove the mat from the platter and put it on the level device it. Avoid large cabinets or locker due to possible vibrations. It should be a non-vibrating stand, rack, or something similar. Put everything in a horizontal positionįirst of all, you need a solid base for your turntable. NOTE: Be very careful and cautious when performing this adjustment in order to handle gently with very sensitive equipment, Plug off your turntable and use proper toolsġ. ![]() We will adjust the balance of the tonearm, tracking force of the cartridge, antiskating adjustment, and cartridge alignment. Let's go through the basic parts explained in this guide. We will show the basic setup which should fit the most turntable types. Even if your turntable is already set up by the manufacturer, you should check everything by yourself.Įvery turntable basically has the same adjustments. When you set up your instrument, you must take care of every single detail that can influence the sound quality. ![]() It will reproduce every single input, good or bad. The turntable is a precise and sensitive instrument. Let's go through this step-by-step basic guide and tune up your turntable as it should be. ![]() If you do it poorly, you will get the same results. If you expect to enjoy your Vinyl records and their gentle sound then you should set up your turntable in the right way. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |